Idle campaigns left active: the hidden database load in VICIdial
Campaigns nobody dials still cost database time while they're set to active. Why that happens, what it cost one floor, and how to clean them up safely.
How many campaigns on your system are set to active? Now, how many did anyone dial this week? If the first number is bigger, the gap costs you database time every minute of the day, whether or not a single agent is logged in.
On one floor we measured, idle campaigns left active with large hoppers were 41% of all database time. Two fifths of the database's work went to campaigns nobody was calling.
What an active campaign does on its own
An outbound Campaign dials from its Hopper, a small, fast holding area for the leads VICIdial plans to call in the next few minutes. Every minute, VICIdial takes each campaign's settings and lists and tries to top that hopper up.
That top-up is database work. VICIdial reads through each Lead list attached to the campaign, the batches of leads you loaded, to find ones it's allowed to dial and loads them in. An active campaign gets that work every minute, with agents or without them.
flowchart LR
A[Every minute] --> B[Hopper top-up]
B --> C[Active campaign with agents]
B --> D[Active campaign nobody dials]
B -.-> E[Inactive campaign skipped]
C --> F[(Database time)]
D --> F
C --> G[Leads dialed]
D --> H[Leads nobody calls]Why big hoppers make it worse
Minimum Hopper Level is how many leads VICIdial tries to keep in a campaign's hopper. The sensible size is slightly more than the number of leads the campaign goes through in a minute.
With Automatic Hopper Level on, which is the default, VICIdial works the size out from the floor itself: active agents, times the Auto dial level (how many lines it dials per agent), times how many Dial timeout periods (how long a call rings before VICIdial gives up on it) fit in a minute, times a multiplier you can adjust. Automatic Hopper Level vs a fixed level explains the trade-off.
The trouble starts when a big fixed number outlives the campaign that needed it. A hopper sized for a full floor, on a campaign nobody dials any more, keeps VICIdial working through lists for leads no one will call. If the hopper itself is still fuzzy, start with what the VICIdial hopper is.
Clean-up without stranding a shift
- List every campaign set to active. The campaign's Active setting is where VICIdial switches it on or off.
- Check your call reports for the last couple of weeks. An active campaign with no calls in that time is a candidate.
- Ask the manager who owns each candidate before you touch it. A campaign that dials once a month still has to be active on that day.
- Set the ones nobody needs to inactive.
Right-sizing the hoppers you keep
For a campaign on a fixed level, set Minimum Hopper Level from the floor you run today, not the biggest day you ever had. Work out how many leads the campaign goes through in a busy minute and set it slightly above that.
For campaigns on Automatic Hopper Level, the size already follows the agents logged in. Check the multiplier instead. It runs from 0.1 to 2.0, and anything above 1 loads more leads than the formula would on its own.
Then watch for hoppers that run dry after the change. An empty hopper leaves agents idle, and nothing on the agent screen tells them why.
What you get back
The time those campaigns used goes back to the work your floor actually feels: saving statuses, handing answered calls to free agents, keeping agent screens up to date.
This matters most in a cluster, where every dialer leans on the same database machine, as the cluster guide explains. On the clusters we run, the cluster page shows each campaign's dial level, hopper and drops against its limit, and warns before a hopper runs dry. A campaign you still need won't go quiet unnoticed after the clean-up.
If your floor fits on one server, the same clean-up applies there; compare our plans for that size. When it's time for separate machines, see what a cluster for your floor costs.
Related from VICIfast
- Is VICIdial free? The full monthly billServer, minutes, numbers and admin hours, priced, for a 20-agent floor both ways.
- What managed VICIdial actually costsFixed monthly plans by server size - no per-seat licence fees.
- Work out your per-agent dialer costModel seat pricing versus a fixed-cost VICIdial box.
- Shared-CPU plans from $49/moFive tiers from Launch to Ultimate. Per server, never per agent.
About VICIfast
We run VICIdial servers for call centres, so you don’t have to. You get the dialer set up, secured and kept running — we handle the server, the updates and the backups. Bring your own phone carrier at no markup, or use VICIfast Voice, our own US calling and numbers, from $0.0085 a minute. From $49 a month per server.
Questions? Call +1 636 556 0022 and talk to someone who runs dialers.
Citing this article
VICIfast Engineering. “Idle campaigns left active: the hidden database load in VICIdial”. VICIfast LLC, November 22, 2026. Retrieved from https://vicifast.com/blog/vicidial-idle-campaigns-database-load
Have questions?
Related posts
You might be interested in
Guides & tutorials
When a CRM polls VICIdial once per agent: the load you don't see
Guides & tutorials
Why searching a lead by phone number freezes VICIdial, and the missing index

Guides & tutorials
Keep the call log small: log archiving on a busy VICIdial database

Guides & tutorials
Reports and tools that slow a live VICIdial floor
VICIfast newsletter
Liked this? Get the next one in your inbox.
We ship the kind of stuff you just read - concrete, numbers-first, no drip. One email when a new post goes live. Unsubscribe in one click.
Comments
No comments yet - be the first.

